Pacific RGB G1/4 PETG Tube 16mm OD 12mm ID
Make your system a showcase for all to see with the newest member of Thermaltake Pacific Series – the Pacific RGB G1/4 PETG fitting, specially designed for enthusiasts to meet the needs of setting up a complete but stylish water cooling system. A RGB LED lighting controller is included. With a patented circular 256 multicolored LED light and produced by durable copper, Thermaltake takes every detail seriously.
Pacific RGB G1/4 PETG Fitting Introduction
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.
Patented RGB 256 Colors LED Light
The fitting comes with a special engineered LED light that can maintain color and brightness uniformity. The lighting effect is visible from all directions and adds style to the chassis.
Taiwan Patent: M523966
China Patent: 201620920987.3
RGB LED Lighting Controller – Adjust LED Brightness
Users can adjust the illumination of the lighting into three different phases by pressing the “BRIGHTNESS” button.
Click the icon for function display
RGB LED Lighting Controller – Switch Over Between 7 LED Colors
The “MODE” button allows users to switch to blink function and set a solid color for the lighting. Users can choose from blue, green, red, white, orange, yellow and purple to brighten up their builds.
Click the icon for function display
RGB LED Lighting Controller – Cycle Through a 256 Colors
By simply clicking the “CUSTOMIZE” button, users can start to enjoy their liquid-cooling systems with a multicolored lighting show.
Click the icon for function display
High-Flow and Leak-Free Design
Made in Taiwan, the fitting allows proper connection to G1/4 ports, securing properly to cooling components while providing an even seal around the tubing. The fitting is included two preinstalled O-ring.
For tubes:
- Outer diameter: 5/8” (16 mm)
Remarkable Expansion
Thermaltake offers a full line of Pacific Series components for enthusiasts to build up aesthetically-superior water cooling systems by incorporating externally-modular upgrades for their chassis.
Thermaltake Riing RGB Controller Cable (Optional) – Can connect multiple RGB LED lighting controllers at the same time, and offer users a more flexible way to control their RGB fittings
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup
- It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
- DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
- Fill the reservoir to the top as it will prevent air from going into the pump
- If necessary tilt the system slightly from side to side to bleed the air out of the loop.
- Place some paper towels under fittings and joining points to test for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Cautions
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant; it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
- Before storing your water cooling components, please clean, rinse, and dry them to ensure a longer lifespan for your components.
Thermaltake recommends the following steps to be taken after completing your water loop setup:
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing corrosion in the entire cooling system – copper, brass, nickel, aluminum, and steel.
- Fill the reservoir with coolant and cycle the power on and off several times while the pump pushes the coolant into the loop.
- DO NOT let the pump run dry; turn off the power immediately if there is no liquid entering the pump.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system slightly from side to side to bleed air out of the loop.
- Place some paper towels under fittings and joining points to check for leaks.
- Run the loop with the fill port open for about 24 hours to completely bleed air out of the loop.
- Before starting, flush your system correctly to prevent any coolant or unwanted particles from sticking to your tubes, radiators, and other cooling components.
- Note that coolant might fade over time.
| P/N | CL-W133-CU00BL-A |
|---|---|
| MATÉRIEL | Copper |
| Dimensions | Ø25 x 31.4 H mm |
| Weight | 720g |
| Compatibility | 16mm OD /12mm ID hard tube |
| Threads | G ¼” |
| Note | 6 Pack (6 Fittings with 1 LED Controller Box) |
